Sheet Metal · 2022年5月16日

How To make Plastic Mould

How To make Plastic Mould

A complete account of the very many methods of mould making would be out of place in a book devoted to the causes and cure of faults in injection moulding.

There are several excellent articles on the subject to which reference can be made. However,to assist in the understanding of how and why problems occur in connection with the mould,a brief sketch of the main mould-making methods involved will be included.

The chief process used is machining, in which the shape to be generated is cut on a lathe or milling machine to the required dimensions. Cutting of very hard steels is difficult so softer steels are used and subsequently hardened or nitrated.

During hardening, the heat treatment which the metal receives may cause stresses which were present in the metal block to be relieved and slight distortion may result.

The use of normalized steels help to reduce this,but a number of annealing treatments as the machining proceeds may be necessary with very accurate work. Most metals can be machined and for simple circular shapes the lathe is the most useful tool.

A modification of machining is die-sinking, in which a negative pattern is used which a pantograph tool will follow to generate the appropriate shape.

Great accuracy is possible as the panto-graph can be arranged to give a reduction of dimension of as much as 10:1 compared with the pattern.

Engraving also uses a panto-graph and is chiefly used for lettering-Where repetitive work is done,numerically controlled (N-C) machinery is used.

It is expensive and the work load needs to be considerable with a large saving of labour before its use can be justified.

Very hard steels can be worked by either electro-chemical machining (ECM) or electric-discharge machining (EDM), often referred to as spark erosion.

ECM is very rapid and 1 in3/min of metal can be removed each minute for each 10 000 A of current,which is obviously at very low voltage.

Surface finishes are good but electrodes,which are of suitable shape to generate the form required,are expensive. EDM is generally used for smaller jobs and is a substitute for die sinking.

Blind holes are quickly generated and sharp angles are possible, dimensions better than 0 001 in being easily obtained.

Newest machines employing transistorized pulse generators which produce very rapid sparking give little electrode wear and a good surface finish.

Electrodes are reasonably easy and inexpensive to make,graphite and copper being preferred materials.
These methods of mould making involve cutting metal away from a form.

Two other methods in use involve the reverse, namely,building up metal to give the desired shape.

Electroforming is a process in which metal is electrically deposited on a reverse model of the shape to be formed and the shell of metal thus produced is backed with a fusible casting alloy such as Hoyt metal or Kirksite.

Cooling coils of soft copper pipe can be incorporated into the alloy backing. In metal spraying a low melting point alloy is flame sprayed on to a positive model and the shell so formed is backed with a similar alloy.

Because the alloys used in both these processes are softer than desired the forms are mounted in a steel bolster and the locking force is taken up on hardened steel pads incorporated in the bolster.

Cast metal moulds of aluminium,zinc,Kirksite and beryllium copper are also used satisfactorily in injection moulding.

In common with all metals, their thermal conductivity is relatively good (better than 0-1 cal/cm s0C,Be/Cu being about 0.5 cal/cm s°C) and even with those alloys of very low melting point (c- 160°C) there is no danger of the hot plastic melting the mould.

However,care must be taken to minimize flashing of the mould because this is always accompanied by excessive air-venting with its consequent production of heat.


How to determine the injection molding machine?

Successful injection moulding depends on the ability of the machine to operate under the correct conditions of pressure,temperature, and speed of operation for the component being moulded and the material being used.

It also depends on the ability to control the conditions of operation within close limits for long periods and on the exact repetition of the cycle of operations many thousands, perhaps millions,of times.

These requirements can be considered first in terms of whether the machine is basically suited to the job, and then as to whether it can be controlled to the limits required.

Determination of whether the machine is capable of meeting the demands to be made upon it can be a matter of trial and error,but if some fairly straightforward calculations are made it is often possible to decide on the feasibility of a job without going any further.

Some assumptions need to be made and accepted because a full mathematical analysis of the injection moulding process is extremely complex and is not the kind of exercise which the average practical moulder would wish to undertake.

If the assumptions are accepted, it becomes possible to arrive at simple mathematical approximations which will give results close enough for the purpose required. The type of information needed is:

  • (a) What injection rate is required for satisfactory mould filling? In other words,how long is the injection time to be?
  • (b) Assuming the injection rate in (a),what will be the pressure requirements?
  • (c) With the pressure requirements of (b) and the injection rate of (a),what amount of hydraulic fluid will be required for actuating the machine, and how big a pump motor will be required to give the rate of flow at the pressure needed ?

Having decided on these matters,the question as to whether the machine can be controlled accurately over the required number of cycles and at the desired rate becomes a matter of machine mechanics.

August 17, 2020 plastic mold

Link to this article:How To make Plastic Mould

Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.:Silicone And Casting,Thanks